Gauges/Rules/Samplers
 
|
Ultrasonic Single Mode Drum Gauge Monitors liquid level with the press of a button
This gauge may be powered by alkaline or lithium 9V batteries (2) not included. Screw into the 3/4" or 2" opening. Gauge accuracy is +/- 0.5 gallon (supplied with 3/4" bung adapter). The monitor settings may be easily switched with the press of a button to calibrate the liquid level in a vertical 15, 30 or 55 gallon or 57, 114 or 128 liter drum. Features a NEMA 4 housing, low battery life indicator, and an LED warning light that flashes every second when fluid level is less than 10% the maximum volume. Compatible with water, wastewater, motor oil, hydraulic fluid and diesel fuel. Not for use with gasoline or other flammables. |
|
Ultrasonic Tri-Mode Drum Gauge Continuously monitors while generating a 4-20mA output
When powered by a 24V external power supply, the gauge will monitor fluid levels continuously. The 4-20mA output can be interfaced to external controllers and test equipment. Gauge accuracy is +/- 0.5 gallon (supplied with 3/4" bung adapter). The monitor settings may be easily switched with the press of a button to calibrate the liquid level in a vertical 15, 30 or 55 gallon or 57, 114 or 128 liter drum. Features a NEMA 4 housing, low battery life indicator, and an LED warning light that flashes every second when fluid level is less than 10% the maximum volume. Compatible with water, wastewater, motor oil, hydraulic fluid and diesel fuel. Not for use with gasoline or other flammables. Note: 4-20mA output function is not available in battery mode |
|
Corrosion-Resistant all Polyethylene Drum Gauge Avoids Spillover This corrosion-resistant all polyethylene gauge is a "must have" for any filling operation. Bright red indicator pops up when drum is nearly full. Fits any drum with 3/4" NPS bung opening. |
|
Accurate At-A-Glance™ Drum Gauges At-A-Glance gauges are the economical choice for measuring the contents of your drums. Leak-proof and reliable, the simple design stays accurate and is built to last. Gauges have a red indicator and black calibrations in gallons, liters, quarters and eights full. On a yellow background making the gauge easy to read in all weather conditions. Optional High or Low Level Audible Alarm sounds at a loud 110 db, operates on a 9V lithium battery. Shown: FG20V55 |
|
Calibrated Sight Gauges for Horizontal Drums
Use with a 3/4" NPT faucet for continuous gauging and dispensing (faucet not included). Replaceable glass tube with protective aluminum frame. Chemical resistant TFE (AFLAS®) seal is use on all three gauges between the glass sight tube and the pipe nipple. AFLAS® is the trade name for a unique fluoroelastomer based upon an alternating copolymer of tetrafluoroethylene and propylene "TFE/P". It has excellent chemical resistant properties and can withstand high temperatures. Other seal materials are available upon request. Standard Gauge has 3/4" NPT carbon steel pipe nipple and coupling for temperatures not to exceed 400º F. Great for petroleum products and other non-corrosive liquids. Stainless Gauge has 3/4" NPT 304 stainless steel pipe nipple and coupling for temperatures not to exceed 400º F Ideal for mild corrosives. PVC Gauge has 3/4" NPT PVC pipe nipple and coupling for temperatures not to exceed 140º F. For use with more aggressive liquids. Note: Faucet not included
Shown SG55A |
|
Glass Sight Drum Gauge Shows Actual Liquid Level Heavy duty glass sight gauge shows liquid level at a glance. Fits 3/4" NPS bung. Plated steel housing is 22" high. Has female outlet for 3/4" NPT faucet (not included). Standard Gauge has Buna-N seal. Ideal for petroleum products. Chemical Gauge has Viton® seal. Use with a wide range of chemicals. Shown SG55S |
|
Versatile Fill Drum Gauge Fill the first container to desired level and record fill gauge reading using built-in reference marker. Subsequent containers can be filled until level indicator reaches reference marker. It's that easy to get accurate filling every time! Designed for use with lower viscosity, non-sticky, liquids. Fits any steel drum with a 2" or 3/4" NPS opening. 23" long. Plastic non-threaded 2" adapter included. Adpter allows access of a 1 1/4" hose or pipe, so filling and gauging may be done simultaneously. |
|
55 Gallon Drum Gauge Stick Simple, reliable gauge stick is calibrated in gallons for both vertical and horizontal drums. Hardwood stick has heavy clear-coat finish for long service life. 5/8" x 5/8" x 48" long. Will not fit through 3/4" bung opening. |
|
Kolor Kut® Gauge Pole Indicator Paste Paste is applied to the gauge stick or pole before use. Use KolorKut® Fuel Paste to find the absolute fluid level of gasoline, diesel fuel, kerosene and other hydrocarbon chemicals. 2.25 ounce jar. Use KolorKut® Water Paste to find settled water content of the container. 2.50 ounce tube.
Shown KK003 |
|
DIPTAPE Visual Level Indicators Simply unscrew the top cap to check level. Slowly pull graduated tape up; when liquid level is reached, the tape locks onto the magnet inside the float and indicates level of liquid in drum. Scale is calibrated in 1/16" and 1mm increments for accurate measurement. When finished, push scale down and replace cap. Stainless Steel DIPTAPE Level Indicator has all 316 stainless wetted parts. Works with most liquids, including chlorinated solvents. Brass DIPTAPE Level Indicator has Buna-N float for oils, fuels, mild solvents. PVC DIPTAPE Level Indicator has PVC wetted parts. Designed for lower cost, general purpose use. Screws into 2" NPT bung opening. |
|
Hardwood Gauge Poles Durable hardwood poles are perfect for gauging below ground tanks, railcars, tank trailers. Large, ink-filled graduations in inches and feet. Heavy catalyzed clear-coat finish. Nylon bottom tip protects pole end. Folding Poles have multiple sections with snap-locks at each joint. Folds for convenient storage and transportation. Shown WP6 |
|
Shatter-Proof Liquid Sampler Simple-to-use sampler. Dip into drum/container, put thumb over 3/16" diameter hole in tapered end, remove sample. Low density polyethylene is heat resistant to 120º F. 41 1/2" long x 1 1/8" diameter. |
|
Polypropylene Sampler All polypropylene drum thief makes sampling a number of drums quick and easy. Samples are readily taken by just placing thumb over the top end of tube. Won't break like glass. |
|
Polyethylene Coliwasa Samples Liquid Waste Simple design for rapid sample collection. Lower tube to desired depth. A light tug on cord while raising the unit sets the check valve, trapping the sample inside. Plastic rod inside tube allows sample to be collected at any depth. Dispenses easily into appropriate container. Sampler holds approximately 3 ounces per foot. |
|
Polypropylene Coliwasas Economical, durable Coliwasa is made of see-through polypropylene for superior resistance to chemicals and breakage. Neoprene stoppers with TFE film coating on top and bottom for improved safety, stick resistance, and sample transfer (sampler can serve as a container for non-hazardous samples). Take representative samples from top to bottom of buckets, drums, tanks and tankers. Handles liquids, slurries, sludge, and semi-solids. Resists acids, alkalies, hydrocarbons, ketones, aldehydes, esters, oxidizers, and glycols. Optional Coupler Set combines two sections of 1" Coliwasa to increase sampler length and compatibility of application. Optional Purge-Squeegee Kit allows rapid and neat emptying of viscous samples. Avoids spillage and helps to decontaminate while automatically cleaning the inside and outside of the sampler tube. |
|
Ethanol Samplers
Need to know the percentage of your ethanol? Take a sample and test it. Ethanol samplers have a 2" stick-out on the bottom for ready fill sampling of liquids involved with blending fuels and ethanol production and transfer. These samplers differ from standard coliwasa style samplers in that they have silicone stoppers which are more compatible to ethanol. They are available in 5 lengths of 1" I.D. polypropylene. Shown ETS139E |
|
Samples the Big Jobs Leakproof high-density polyethylene sampler is ideal for caustics, acids, and most other chemicals. "T"-handle for extra grip. 16 ounce low-density polyethylene bottle screws into sampler, large 38 mm opening is easy to drain. For tanks and open-head drums with cover removed. Will not fit through 2" NPS bung opening. Shown S17 |
|
5 Gallon Pail Sampler |
|
Economical Polypropylene Sampler |
|
Multi-Purpose Stainless Steel Dippers The S1201 dipper has an overflow hole in the cup and a hook for convenient hanging. The S1047 dipper has one piece construction, with no cracks or crevices to collect sample residue. Shown S1201 |
|
Fluoropolymer Samplers for all Liquids, Even Sludge Dipstick™ allows sampling of free-flowing liquids from any source. Unique push-seal bottom seals securely. Outer Fluoropolymer indicator ring for marking fluid levels.
Shown ND3052 |
|
Glass Drum Thief Easy sampling and retention by placing thumb over open end. Easily broken for disposal. 43" long. |