Heaters

View larger image

Portable heat environment keeps your materials at working temperature!

• Patented heat spreading technology for fast, even, consistent heating
• Low energy consumption
• Compact, lightweight, portable fold-up design
• Certified to UL/CSA Safety Standards

     The powerblanket® HOTBOX is the most efficient method for heat soaking temperature-sensitive materials. Road crews, warehouse managers, and construction contractors everywhere use the HOTBOX to heat and maintain working temperature. Portable fold-up design for ease of transport. Plugs into a standard 120 volt outlet. Adjustable external thermostatic controller is included. Internal thermostat will top out at 150° F (± 10°).

View larger image

Get the job done faster and use less electricity!

• Full coverage heaters require less wattage to obtain optimal  heat
• ETL Certified to UL/CSA Safety Standards
• Indoor or outdoor use

powerblanket® uniform heat spreading technology heats up faster, cools down slower, and uses much less electricity than conventional band heaters. Use on plastic or steel drums. powerblanket® heaters come ready to use. Just unroll, wrap around your container, and plug into any 120V outlet. Supplied with adjustable straps to ensure proper fit on containers that vary slightly in size.

Rapid Ramp Heater (RR) doubles the watt density to quickly heat up to a maximum temperature of 100° F then automatically backs down to one-half power to maintain temperature. This automatic function is all internal and preset. In an indoor environment with an ambient temperature of 70° F, heater PBL55-RR will heat a 55 gallon plastic drum filled with 70° F water to 100° F in 5.5 hours. It would take two to three band heaters to equal the heating power of one powerblanket® heater. Rapid Ramp Heaters do not have an adjustable thermostat.

Pro Heater (PRO) includes an in-line thermostat with heat probe for measuring the temperature of the liquid in the container. The thermostat is fully adjustable with a temperature range from -23° F to 160° F maximum temperature.

View larger image

Heats efficiently and safely in flammable and explosive areas!

• Designed for use with 275 gal. plastic IBC in a metal cage
• Good for Class 1 Division 1 & Class 1 Division 2 areas
• Operates on 240V or 120V AC power
• CE, ATEX and IECEx certified

View larger image

Your IBCs need energy-saving heat, too!

• Rapidly heat a wide variety of materials with much less energy
• Install easily and fit nearly every standard tote tank, plastic or steel
• Feature powerblanket® patented heat spreading technology
• Certified to UL/CSA Safety Standards

 powerblanket^® IBC/tote heaters are flexible wrap around surface heaters with patented “heat spreading technology” that delivers a barrier of heat to temperature-sensitive materials and ensures constant and safe temperature. They fit nearly every standard IBC/tote tank, utilizing adjustable nylon straps. Adjustable PBL-THERMO thermostatic controller is standard on all powerblanket^® IBC/tote heaters. Includes an insulated lid that helps contain heat, conserve energy and shorten the time it takes to heat your product. Heaters plug into a standard 120V outlet, generates 1,440 W and draws 12.00 amps.

View larger image

Puts a lot of heating power into your IBC...and protects your product

• Full coverage "plug and play" system
• Fits plastic tote tanks 40" x 40" to 48" x 48"
• Available in three heights: 36", 40" and 48

Tote tanks and IBCs containing slow moving product such as honey, molasses, lube oil or other non-hazardous liquids can be difficult to dispense, especially when stored in a cool area or when winter strikes. The Wrap-Around design allows non-invasive heating and will not contaminate or scorch product. Thermostat is adjustable 50-160° F.Two separate heating zones help prevent product and heater damage. Constructed of silicone impregnated cloth facing and liner filled with 1/4" fiberglass insulation, the heater blanket is held in place with adjustable nylon straps with buckles. Blanket has a small opening for valve accessibility. Supplied with a 6' power cord with standard plug: 120VAC - NEMA 5-15 or 240VAC - NEMA 6-15. An optional insulated top cover is available for faster heat-up and efficient temperature maintenance.

Shown THTR48-120

View larger image

The most popular drum heater on the market!

• Increase flow rate of viscous materials
• Heater models for steel and plastic drums, pails
• Choice of heating controls

Durable heaters install instantly with spring-loaded toggle clamp. Rugged aluminized steel construction with internal fiberglass insulation (except LIMD55-115). Choice of three heating controls. All are equipped with neon pilot light and 6' power cord and are warranted for one year. UL-Listed and CSA certified.

AGM and TRX Thermostat Control with Three-Heat Switch designed for use on steel drums and pails with materials with good heat receptivity. Thermostat bulb senses temperature in an area distant from the heating elements. Three-heat switch allows three wattage ranges per thermostat setting. AGM heaters operate on 120 volts, up to 1750 watts, with standard 3-prong plug. TRX heaters operate on 120 or 240 volts, up to 1920 watts, with NEMA plug. For steel drums and pails only, that do not contain a removable plastic liner.

SRX Infinite (Variable) Control with Three-Heat Switch designed for use on steel drums and pails with materials that are subject to charring, burning or separation, such as food, chocolate, honey, light oils, and undercoating materials. These heaters do not have a thermostat and will not automatically reach and hold a given temperature. The function of the infinite control is to cycle a current on and off into your material. This provides a gentle warming action to the material that is being heated. Infinite control operates within each of three wattage ranges for closer heat control. For steel drums and pails only, that do not contain a removable plastic liner.

LIM Pre-Set (Non-adjustable) Thermostat designed for heating materials in high density polyethylene drums and pails. Thermostat is factory set; will not exceed the maximum plastic-safe temperature of 165° F recommended by many plastic drum manufacturers. Simple on-off power control.

For indoor use only. Units are not moisture-proof or explosion-proof. Not for use with flammables or near a flammable area.

AGM, TRX and SRX series are not for use with plastic drums and pails or drums and pails that contain a removable plastic liner.

Caution: Allowing liquid in a container to fall below the level of the heater will render the heater ineffective and could irreparably damage the baked on epoxy phenolic lining in lined steel drums and pails.

Note: NEMA plug 5-15P is a standard three-prong plug. All other plugs require matching NEMA outlet.

View larger image

Versatile AND inexpensive!

• Tough fiberglass and silicone
• Complete with adjustable thermostat
• UL/cUL Recognized

     Tempco flexible drum heaters are the economical choice for heating liquids in drums or pails. Vulcanized 3-layer silicone rubber construction is reinforced with fiberglass, making it tough, long lasting, and resistant to a wide range of chemicals. Non-stick silicone rubber surface is easy to clean. 120 volt models are supplied with 6’ cord with standard three-pronged plug. 240 volt models have a 6’ cord without plug. When not in use, the heater can be rolled for convenient storage. Use one heater on the lower third of the drum or pail or attach more heaters to the container to increase wattage and speed up the heating process.

SDH Series Heaters are not for use with plastic drums and pails or drums and pails that contain a removable plastic liner.

Caution: Allowing liquid in a container to fall below the level of the heater will render the heater ineffective and could irreparably damage the baked on epoxy phenolic lining in lined steel drums and pails.

Important: Containers with an outer diameter ± ½” the O.D. listed in the table require a custom made heater. 240V heaters for 5 gal. pails, 15 & 30 gallon drums and heaters without thermostats are also available by special order. Call Customer Service at 1.800.776.3786 for details.

Shown SDH55120-3

View larger image

Puts all the heat exactly in the right spot

• Concentrates heat at bottom of open-head steel drums
• T-316 stainless steel sheath

“Cold riser" design concentrates heat at the bottom of the drum. Powerful 5000 watt drum heater has built-in thermostat that controls temperature between 70º F and 250º F.  A minimum liquid level of 10" above the bottom heating coil is required. Risers are 36" high with a 19” diameter heating coil.

Supplied without a cord or plug and must be wired according to local electrical code. Operating instructions and a wiring diagram are included with each heater. This heater is for use with water-based solutions and must not be used with flammable or oil based liquids.

View larger image

Save money by buying just the heat you need!

These added value electric drum and pail heaters deliver up to 1250 watts of dependable heating power, 25% more power than other heaters in its price class. The 0º–550º F adjustable thermostat provides a wide range for different heating requirements. Supplied with 6' cord and standard three prong plug. Rugged aluminized steel construction with quick release clamp.

Not for use with plastic drums and pails that contain a removable plastic liner. Not for use with flammable materials or near a flammable area. For indoor use only. See our other heaters designed to heat plastic drums.

Caution: Allowing liquid in a container to fall below the level of the heater will render the heater ineffective and could irreparably damage the baked on epoxy phenolic lining in lined steel drums and pails.

Shown 55VAL

View larger image

Puts the heat right into the product!

• Improves flow of viscous liquids
• 60 - 250° F thermostat with over-temperature cutout

Immersion heaters put the heat right into the liquid for the most efficient heating. Only 4" of riser is heated, allowing liquid level to fluctuate without damaging the heater. Fits through 2" bung opening in steel 55 gallon drums. Adjustable mounting bracket positions the heater away from the drum wall and above sludge buildup at the bottom of the drum. Pilot light indicates whether heater is cycled on or off. All heaters are single-phase and have NEMA 1 control housings.

No cord or plug is provided - consult your local electric code for the proper wiring techniques for the environment in which the heater will be used. Operating instructions and a wiring diagram are included with each heater.

Shown TAT30005

View larger image

Efficiently puts heat into your IBC - and keeps it there

• Won't harm plastic IBCs
• Choice of single or dual zone heating
• Operates on 110V AC power
• CE certified

These high-efficiency IBC blanket heaters have a silicone-insulated spiral-wound resistance element housed in a composite nylon-coated woven fiberglass jacket. Both heaters are equipped with four pairs of easy-connect buckles and straps for easy attaching and removal.

IBC1 Single Zone Heater has a heating element housed in the lower two thirds of the unit. It is designed for winter warming applications up to 104º F. Heats liquid 1º F -5º F/Hour. Adjustable jacket 160"-169.5" L x 37-1/2" H.

IBC2 Dual Zone Heater has an upper and lower heating element designed for faster heating up to 140º F. Adjustable jacket 160"-169.5" L x 37-1/2" H.

IBC1-2LID Optional Insulated Lid helps to contain heat for added efficiency.

IBC1-2WPC Optional Waterproof 2-Piece Cover protects heaters from moisture and allows blanket heaters to be used outdoors under general weather conditions. Withstands temperatures to 0° F. Includes center flap for fill port access. Made of 0.5mm PVC coated polyvinyl. Color is bright orange.

Note: When ordering your heater, be sure to state your container’s dimensions and type

Shown IBC2 with IBC1-2LID

View larger image

Got a lot of drums to keep warm? Hot Box is MUCH better than regular drum heaters

• Units for pails, 1, 2, and 4 drums/IBC
• Available in electric or steam
• Heavy-duty steel construction
• Custom sizes available through special order

Drum heater and pail heater Hot Boxes are steam or electrically heated which facilitate the heating and melting of various materials in one, two, or four 55-gallon drums or different size pails. The 4-drum hot box may also be used to heat an IBC. Standard features include spill containment, and a 14 gauge welded carbon steel exterior, 3" of #6 density mineral wool insulation throughout.

Options available include shelves, temperature controls, air circulation blower, zero ground clearance, and outdoor service package. Call Customer Service at 1.800.776.3786 for details.

View larger image

Ideal for safely warming honey

Primarily designed for use with plastic pails, these 5 gallon aluminized steel pail heater is factory engineered to maintain a constant heater band temperature of 165° F while in contact with a full pail.  Fits plastic or metal pails, tapered and straight sided pails 9 1/2" to 12" in diameter. 3 1/4" wide band for better heat dissipation. Equipped with a hose clamp style screw mechanism for installing heater to pail. Screwdriver is required. Supplied with 6' cord and three-prong plug. 120VAC, 100W. Not for use with flammable materials or near a flammable area. For indoor use only.

Note: Use only with high density plastic pail to insure pail will not melt.

View larger image

Don't take chances! Flammable materials demand the right heater!

Quality silicone rubber and fiberglass drum heater is moisture-proof for durable long life. Simple spring and hook fastener for easy installation and removal. Adjustable dual set-point temperature controller assembly has a 6’ cord with a standard 120V NEMA 5-15 plug. One set-point is set at a high temperature limit and connected to a red indicator light.

High limit cut-out limits band temperature to 80% of "T" rating, the auto-ignition temperature of the flammable product (National Electrical Code Article 501). Heaters for 30 gallon drums and different voltages are available by special order. Call Customer Service at 1.800.776.3786 for details.

Note: Specify "T" rating when ordering.

Shown SRH55T-115-T3

View larger image

Put efficient heating power into your pails

• Pail heater concentrates heat at bottom of 5-gallon steel pails 
• Polished 316 stainless steel heating element sheath

“Cold Riser” design hangs over the edge of the pail. Heating elements are contained in coil section to concentrate heat at the bottom of the vessel. For use with water-based solutions and must not be used with flammable or oil based liquids. Standard thermostat adjusts 70º - 250º F. Supplied with 6' cord with standard 3-prong plug. Optional 120º - 570º F adjustable thermostat and 230V model are available by special order.

Note: Requires a liquid level of 5” minimum above the bottom heating coil.

View larger image

Shed the water weight and watch disposal costs go DOWN!

• Heater evaporates up to 1.3 gallons of water per hour
• Shuts off when all the water is evaporated

Unique heater fits standard 55 gallon steel drums, reduces the volume of watery waste requiring disposal. Rugged aluminized steel housing. Equipped with a thermostat and resetable high limit cut off switch. When the water based material is reduced below the drum heater, the high limit switch will activate shutting off the heater.  Once the container is refilled, you will need to manually reset the heater by pressing the black reset button located on the front panel. Thermostat range 70º – 250º F. Operates on 240V, 1-Phase, 3,000 watts. Heater supplied with 6' cord and high ampere plug. Not for use with flammable materials or in hazardous areas.

Industrial outlet required to match NEMA plug.

Note: Not for use with plastic drums or drums that contain a removable plastic liner. The baked on epoxy phenolic lining in lined steel drums will discolor if liquid is allowed to fall below the level of the heater. EPA Regulations require the user to ensure that the waste material being reduced will not release toxic material into the atmosphere.

View larger image

Puts ALL the heat into the drum - and helps keep it there!

Most efficient method of temperature elevation, freeze protection and viscosity control of non-hazardous materials. Wrap-around blanket is filled with 1” thick high density fiberglass with VELCRO^® closure for quick installation and has a silicone-impregnated surface to resist most chemicals and moisture. Blanket is 33-3/4" tall, fits 22-1/2" diameter 55 gallon drums.

Drum Heater has a built-in digital thermostat and 6' cord. 240V heaters are not supplied with a plug. Heating elements are located in the lower third of the blanket to avoid overheating of partially filled drums.

Insulating Drum Blanket does not have built-in heating elements; can be used over any silicone rubber heater. Withstands up to 500º F.

Shown FG55-120

View larger image

Heater/Cooler units have embossed channels for steam, hot or cold water, or refrigerant*, All welded 18/16 gauge carbon steel construction with smooth inner panel for efficient heat transfer. Features quick acting toggle clamp for easy installation and removal and an insulated handle for safe handling. A single section unit will heat a 55 gallon steel closed drum from 60° F to 160° F in 4 hours using 150 psig steam.  1/2" IPS (iron pipe size) female inlet and outlet pipe couplings. Multi-section units are supplied already piped together.

Hinged-Back Style has a continuous hinge at the back of the unit for easy installation and removal.

Slip-Over Style has a continuous jacket that is designed to slip over the top of a container. Expandable opening at one end has a toggle style clamp to secure the unit in place.

Drum Cradle Style is available in carbon steel only. It has a heavy steel pipe frame and three half sections of heating/cooling channels. Cradle unit will heat a closed, properly ventilated 55 gallon steel drum of water from 60° F to 160° F in approximately 2 1/2 hours using 150 psig steam. The cradle unit is equipped with a 3/4" MPT (male pipe thread) inlet and outlet.

Immersion Style is designed to come in contact with the liquid it is to heat or cool by placing it directly into a 55 gallon drum. 3/4" MPT connections standard on units without hoses. Maximum operating steam pressure without the use of hoses is 250 psig and with 3/4" I.D. x 42" steam hoses, 200 psig working pressure at 380° F. Not available with painted finish.

Hoses, if included, are steam hoses made of rubber with wire braid reinforcement.

Carbon Steel Models have a light coating of oil on the exterior surface to help prevent rust.

Painted Carbon Steel Models have a royal blue exterior, baked on, painted finish for more substantial rust prevention.

Stainless Steel Models are made of stainless steel platecoil.

*If using refrigerant, please notify your BASCO Customer Service Representative. Plain end pipes or socket weld fittings will replace standard couplings at no extra charge.