Drum Handlers
|
The Iron Men of Drum Handling
A Drum Handler can make your job easier in lots of ways. |
 
|
Morse Hydraulic Lift Karrier™ Drum Handler with Power Options Now, imagine a powered Swiss Army Knife!
Power Lift Karriers increase safety and productivity. Eliminate manual effort to lift and/or tilt drum. Move control valve handle to raise, lower or hold drum in position. Power Lift and Tilt Karriers allow precise and effortless control of lift height and draining angle. Equipped with separate control valves for lifting and rotating. Electric Models have hydraulic pump driven by 110 VAC, 1 phase TEFC motor. Supplied with 3-wire cord, plug and switch. Air Models have vane-type air motor. (Optional filter, regulator and lubricator are available.) Battery Models have 12 volt DC pump motor. Supplied with deep-cycle battery and charger. Note: These models can handle a 55 gal plastic drum with the use of a bracket or rim clap which is required to prevent the drum from slipping through the saddle. See items 4556-P (bracket) and 4560-P (rim clamp) for specifications. They can also accept diameter adaptors for smaller diameter drums, see 55/30 series for specifications. Shown 400A96-110 |
[1].jpg)
|
Drum Transporter and Palletizer Palletize drums quickly and super easily without a forklift!
Raise or lower handle until hooks are positioned directly below the drum rim. Dual ratchets take over and raise the drum as the handle is pulled down. Ratchets maintain the handle position so operator holds no weight. You can move the drum or place it the corner of a pallet. Raise the handle, and drum is lowered onto the pallet, making drum handling and palletizing an easy task. Unit rolls easily on (2) 6" polyolefin load wheels with roller bearings and (2) 4" rear swivel casters. Designed for rimmed drums up to 22" to 23 1/2" diameter and 34" to 36" high. |
|
Roto-Lift™ Multi-Purpose Drum Handlers Sometimes it's better to pour a drum sideways - here's how!
Roto-Lift™ multi-purpose drum handlers are ideal for transporting, stacking, and controlled pouring. Two ratchet belt tighteners and nylon belts hold drum securely. Worm-gear rotating mechanism holds drum at any desired angle. Welded steel frame has single post design for maximum operator visibility. Battery Powered Unit lifts drum at 17 feet per minute. Uses standard 12 volt DC deep-cycle battery (included). Built-in charger plugs into standard 110 VAC grounded outlet. Batteries are included. Air Powered Unit lifts drum at 17 feet per minute, uses 50 CFM @ 80 psi. Supplied with filter, regulator and lubricator. Manual Unit has foot-operated hydraulic pump and hand crank tilting. Lifts drum at 5 feet per minute. Unit has 25 1/2" long legs, 24 3/4" between legs. Rolls on 3" diameter polyurethane front wheels and 4" diameter swivel rear casters. 44" turning radius. Frame requires 6" underclearance. Counterweight Frame Models require no under clearance and allow pallet unloading and drum transport and dumping in close quarters. Supplied with (34) 13.5 lb. counter weights. Rolls on 5" diameter polyurethane front wheels and 4 1/2" diameter swivel rear casters. 61 1/4" turning radius. Note: Counterweight models weigh twice as much as straddle models and require much more effort to position and propel. Optional steel-It or stainless steel units are available for food and/or pharmaceutical applications. |
|
Drum Jak™ Gripper Works Like a Pallet Truck Move and Palletize any rimmed drum!
The Gripper uses two 3" contoured beak design; works with any rimmed steel, plastic or fiber drum, 30 to 55 gallon. 20" lift height is perfect for palletizing drums or accessing secondary containment pallets or scales. The Gripper is also available with scale. Ask your BASCO Customer Service Representative for details. |
|
Drum Runner™ Drum Transporter & Lifter Gets your food drums WAY off the floor!
Handles steel, plastic or fiber drums from 30 to 55 gallon. Simple and dependable clamp mechanism doesn't rely on weight of drum or springs to stay locked, so partly filled drums are held just as securely as full ones. Non-slip foot pedal operates the 1:1 hydraulic cylinder lifting system, folds up to clear narrow aisles and doors. All steel frame has a large steering handle and four 8" diameter phenolic swivel casters for low-effort maneuvering. Dimensions: 62 1/2" H x 54" W x 34" D x 25" lift height. Steel-It® Stainless Steel Epoxy finish is highly chemical resistant and USDA compliant for incidental food contact. Optional Foot Brake operates on rear casters. Increases safety while lowering drum. Shown 4500S |
|
Omni-Lift Karrier™ Multi-Purpose Drum Handler Quickly and easily get drums into your storage rack - without a fork lift!
Versatile drum handler lets one person pick up drums, regardless of position, and raise them up to 72". Handles fully loaded drums up to 800 lbs. or half-full drums up to 500 lbs. Easy-loading cinch-type saddle accepts 55 gallon steel drums (optional adapters available on special order for other sizes). One optional adapter, AP405, is available for 55 gallon rimmed plastic drums. Fool-proof hydraulic system, with hand-operated hydraulic pump. Full lift is obtained in about 45 strokes. 30:1 reduction gear-drive allows drum to be rotated continuously through 360º, forward or reverse, holds drum at any angle desired. All welded steel frame rolls easily on two 8" polyolefin wheels and two 4" swivel casters. Designed for use with pallet racks that have adjustable drum cradles. Minimum clearances required: 7" between drums, 12" between drum and rack upright on right side, 8 1/ 2" underclearance for legs between lowest support beam and floor. |
|
MORSE Mobile Drum Karrier™
This is the faster, easier way to transport, tilt and drain drums. Drum handler can handle up to 800 lbs. Easy-to-operate tilt locks hold drum securely in vertical or horizontal position. Unlocked drum can be rotated through 360º for mixing and draining. All welded steel frame, alloy cinch chain, 8" polyolefin wheels with 4" swivel caster. Weight 95 lbs. Spark-resistant models available by special order. Model: 80I accepts all optional diameter adapters. Ask your BASCO Customer Service Representative for details. Shown 80I |
|
WESCO Drum Jack Here's how to move a single drum without tilting it - and with little effort!
This portable drum jack is equipped with 8" x 2" nylon steering wheels and 1" x 3" nylon load wheels. Overall Height: 47" to top of handle. Overall Width: 28", Overall Depth: 42". Ships unassembled; handle must be attached. Packaging dimensions: 42" x 30" x 21". |
|
Ergonomic Drum Handler
Wesco's exclusive auto grip lock automatically locks the grip jaws closed. Even over rough terrain, the Wesco Gator Grip maintains a positive lock and will not drop a drum. Spring loaded clamp holds any 3/16" or higher drum rim. Swivel casters provide easy movement and steering. Floor lock is standard. Ergonomic design allows 55 gallon drums to be easily raised 20" off the floor. Operator can perform all clamping, lifting and transport operations without ever touching the drum. |
|
Easy Lift™ Economy Drum Transporter Gets you (and your drums) in and out of tight spaces!
Prevents strained back,, pinched fingers, and other injuries associated with manhandling drums on and off pallets. Features the Eagle Grip 1 clamping mechanism and foot operated manual lift to quickly and safely lift drums weighing up to 800 lbs. Locking casters keep the transporter from rolling away on un-level surfaces. Dimensions: 39.50" W x 35" L x 46.25" H. Shown ELE800 |
|
Easy Lift™ Counter Balanced Drum Transporter Got lots of drums to move, but no fork lift? No problem!
With a counter balance to even the load, it's narrow 24" width for navigating through narrow aisles, and its "legless" design for placing drums into tight areas such as cabinets, this unit delivers a lot of value for the money. Dimensions: 24" W x 40" L x 40" H. Standard and Spark Resistant Model features a foot operated manual lift. Power Lift Model is equipped with a 24V battery system and built-in charger. Optional increased lift height and capacity are available. Shown EL600CB |
|
Economy Hydraulic Drum Handler Here's what you want for no-tilt drum transport in tight spots!
Just roll up to the drum, hook on and lift. Pallet truck-type pump handle provides 0.87" of lift per stroke. Polyurethane casters: 8" front, 5" rear. Lift range: 13 1/2" from floor to bottom of standard 34 1/2" tall 55 gallon steel drum. Manually operated top lever clamp secures drum in place. |
|
High-Lift Hydraulic Drum Handler Gotta get your drum onto a pickup truck? No problem!
Extended lift range - lifts 55 gallon drum 42.5" - enough to allow placement of drum on most pickup truck beds, shelves and racks. Easy width adjustment to accommodate a variety of pallets. Just remove lock pin and leg moves easily on caster - no need to lift truck to adjust. Casters with precision roller bearings provide maximum maneuverability, even in confined areas. Foot operated hydraulic pump provides .46" lift per stroke. Lifts standard 34.5" H 55 gallon drum 76.75" to top of drum and 42.5" from the bottom of the drum to the floor. Leg span adjustments 28.24" to 54.75". |
|
Versa-Lift™ Drum Positioners Do It All
Drum handlers lift, grab, stack, tilt, and rotate drums. Welded steel frame has 3" polyurethane front wheels and 4" diameter swivel rear casters for easy moving, 44" turning radius. Dimensions: 42 1/4" L x 30" W. Legs are 25 1/2" long, 24 3/4" width between legs. Straddle requires 6" underclearance. 1000 lb. capacity. Foot-operated hydraulic pump and hand crank tilting. Lifts drum at 5 feet per minute. Electric, Air, and Battery powered models are available. |
|
MORStop Tilt-Brake
When dispensing a heavy drum, especially an unbalanced drum, operators may need to manually lock the pull-chain or crank handle to prevent unwanted drum rotation. The unique MORStop Tilt-Brake mechanism automatically stops and holds the drum tilt angle. MORStop can be used with any of the hand-crank or chain-wheel operated manual-gear-tilt Morse models with capacities up to 1500 lbs. for full drums in the series 185, 285, 400. Order the Tilt-Brake factory installed on new MORSE® drum handling equipment or self install on existing units. |
|
Morse Karrier™ Diameter Adapters
|