IBC Replacement Parts

View larger image

• Made of all plastic material
• Fits Mauser®, Schutz®, Greif® and Varicon cages
• All black in color; gray is available

     IBC replacement marking plate allows your customers to put their product information on cleanly and easily.

View larger image

• Replacement gaskets for Greif®, Mauser® and Schutz® valves
• Gaskets available in EPDM or Viton
• Foil Seals can be put on all valves that you repair

     The IBC replacement parts allow you to repair and reuse your valves.

View larger image

• One way check valves
• Choice of NPT or Quick Disconnect

     IBC replacement parts will help you comply with the EPA's Pesticide Container and Containment Rule for refillable containers.

View larger image

• Keeps valuable product safe
• Vents when plug is opened
• Tamper evident to comply with new EPA regulations

Tamper evident plug stays in the lid without removal but allows manual venting.

View larger image

• All polypropylene screw-on nut for easy connection to IBC
• Choice of NPT or Camlock adapter at the outlet

Highest quality bolted-design valves have nylon collar and foil seal over 2" NPT outlet. Large, easy-to-operate handle. All valves have been tested and passed with UN rated IBCs and will allow controlled flow of product from IBCs.

View larger image

Highest-quality bolted-design valves have nylon collar and polyethylene seals. Large, easy-to-operate handle. Maximum operating pressure 100 psi @ 70º F.

Shown PBVSHMAXFC2

View larger image

• Made of polypropylene for chemical compatibility
• Adapters available for female x male or male x male
• Helps achieve easy no-mess discharge from IBCs

View larger image

Make short work of IBC valve replacement

• Fit popular IBC valves
• Accepts 1/2" square drive extension

Don’t fight the job with ordinary wrenches - this unique steel wrench gets into the tight space around most IBC valves. Snugs up the valve collar after hand tightening the valve into the IBC. ½” drive extension acts as a wrench handle to turn the collar.

View larger image

• Use with 1/2" drive torque wrench to maintain DOT requirements
• Fits all 6" to 9" fill port caps on Composite IBC's

Adjust the stainless steel pins to fit the fill port cap by moving them in or out along the slots on the aluminum bar and maintain the adjustment by tightening the zinc plated steel wing nuts.

Be sure to follow the manufacturer's closing instructions to be in compliance with the container torque requirements.

View larger image

Versatile tool eases common IBC jobs

• Fits popular IBC fill port caps *
• Also opens most 2" and 3/4" steel drum plugs 
• All welded steel construction for durability

Don’t struggle with awkward cap tightening methods. Combination wrench tightens and loosens IBC caps and the vertical cap grabber ends double as wrenches for 2” and ¾” steel drum plugs. Use with a ¾” socket (not included) and manual torque wrench to comply with DOT closing requirements for the IBC fill port cap.

Be sure to follow the manufacturer’s closing instructions to be in compliance with the container's torque requirements. Exceeding the required torque is considered misuse and could damage the fill port cap, negate the UN rating of the container and damage the 3/4" male drive (bolt head) on the tool. The wrench manufacturer will not be responsible for any damage due to misuse.

View larger image

• Made of high density polyethylene
• Keeps dust and foreign objects out of valve assemblies 
• Available with NPT or buttress threads

Ball valve dust caps keeps dust and foreign objects out of valve assemblies during transportation or storage.

View larger image

Precision molded black/blue polyethylene screw caps replace original equipment on plastic IBC's.

Black Standard Cap has plain top without fitting.

Black Plug-Type Cap has 2" NPS opening in center with solid polyethylene plug.

Black Plug-Type Vent Cap has 2" vent plug with PTFE membrane. Provides both pressure and vacuum relief.

Blue Plug-Type has two 2" NPT polyethylene plugs.

Tamper Evident Plug fits a 2" Buttress opening.

Socket Wrench Head makes proper cap installation easy. Fits 1/2" square drive of any ratchet or torque wrench. Welded carbon steel construction with enamel finish.

View larger image

Fusible closure melts in event of fire, releasing dangerous pressure build up inside the container. Pre-assembled unit crimps onto opening in cover, includes a 2" plug with a 3/4" reducer opening and a metal crimp ring for secure installation. A molded, pre-scored diaphragm forms a hermetic, tamper-evident seal. Diaphragm has convenient pull ring for easy removal.

Crimping Tool easily and accurately installs closure.

View larger image

High quality precision castings offer smooth cam-lock operation.

Adapter has 2" NPT male thread and male quick disconnect.

Dust Cover has two sealing loops that can be locked or sealed to prevent unauthorized access. Supplied with Buna-N gasket.

View larger image

We have the right lid for your stainless steel IBC. Highest quality 304 stainless steel with 2B finish. Fits IBC's with drum-type openings.

Flat Lid is plain with no fitting.

Nipple Cover supplied with 3" Girard nipple to accept fusible vent cap.

Poly Vent Cover supplied with 2" poly vent closure installed.

Shown SS2RVL

View larger image

Protect your IBC from dangerous overpressure conditions. Meets UN standards for venting. 316 Stainless Steel. 3" fusible cap melts at fire temperatures, provides 8.295 square inches of venting area. Hydrostatically tested to 75 psig. Supplied with PTFE gasket. Safety Cable is included and retains plug during filling and draining operations. 14 1/2" cable for convenient attachment to the container.

psig = pounds per square inch gauge

View larger image

Precision investment cast valves have reduced port design with solid ball and blowout-proof stem. PTFE seats and seals. 1000 psi WOG. Extra long low-profile plastic covered handle. Handle can also be locked and sealed against unauthorized access.

WOG = Water, Oil and Gas

Shown VSSBV2

View larger image

All IBC remanufactured parts are run through a five-step process:

1. Valves are inspected and any non-function parts are replaced
2. Each valve is disassembled and separated
3. Valve pieces are soaked in pre-clean solution
4. Run through a wash and dry process until specifications are met
5. Cleaned & remanufactured valve is assembled, inspected, sealed, & packaged